Necessary materials and manufacturing methods
Of beads you can make by yourselfseveral kinds of bracelets. They will differ in their appearance, as well as in the complexity of the fabrication, as well as in the materials that will be required to make the bracelets themselves. 
Bracelets on the arm "Snake"
In order to make paired bracelets from beads "Snake", the following materials will be needed:
- nippers,
- pliers,
- wire with memory effect,
- two kinds of monophonic beads.
A wire with a memory effect is aThe wire, twisted into a spiral, which after straightening returns to its normal form. In order to make bracelets with your own hands, it fits perfectly. The essence of manufacturing such products is very simple. First you need to decide how much wire is needed. To do this, it is necessary to determine what kind of bracelets are needed, namely, how many turns they should consist of. To do this, you need to try on the hand a few turns of wire, adjust their number in the desired direction, and then cut the workpiece from the skein. Next, use a pair of pliers to bend one edge of the workpiece to form a loop. Then you need to string the beads. This can be done as alternating different types of beads with the predominance of one of the colors, and in an arbitrary order. However, since the bracelets are paired, they will look the most harmonious if they are assembled the same, or combined according to the assembly scheme. For example, you can alternate three beads of the same color, each other and again three beads of the original color. And on the pair bracelet repeat the same assembly scheme, but make the main other color. After the beads will be strung almost to the end of the wire, you need to make a loop at the end, similar to the loop at the beginning of the bracelet. The second decoration is assembled in this way. 
Bracelet "Tenderness"
For the bracelet "Tenderness" will be needed:
- Strong thread with a needle for beads,
- scissors,
- multi-colored beads,
- two slices of a thin satin ribbon,
- metal hollow cones for jewelry or beads with a wide hole.
In order to make a bracelet "Tenderness"first you need to measure the girth of your hand and determine which bracelet is the width you need. Since "Tenderness" consists of bead threads, the larger the number, the thicker the bracelet will be. Then you can go directly to the fabrication. First of all, you need to thread the beads on the string so that the bead thread is equal to the arm circumference in front of the brush, and the free ends of the thread are about 3 centimeters on each side. Having thus produced a sufficient number of blanks, it is necessary to tie the free ends of the yarns so that a horizontal blank consisting of individual bead threads eventually forms. Then you need to fix on each side of the workpiece a piece of satin ribbon, about 10 cm long each. The resulting attachment points in the form of nodules on both sides should be covered with metal cones, wearing them on a ribbon, with a wide side to the beads, or beads. It remains to bind ribbons to each other in a pretty bow and the original accessory is ready.
Bracelet "Ice"
To make a bracelet "Ice", you need to cook:
- a thin metal chain with wide links,
- wire for beadwork,
- scissors,
- white or silver beads,
- matt glass bead,
- a carabiner for fastening.
You can also purchaseMetallized beads or pendants made of rock crystal. Bracelet "Ice" is assembled as follows. First, a carabiner is attached to one end of the chain, using a sliding ring on it. Then the desired number of suspensions is manufactured, based on the assumption that no more than two suspensions can be attached to one cell of the chain. Then the suspensions themselves are made. For this, pieces of wire are cut off, the length of which will correspond to the length of the suspension. And the suspension can be different in length. One end of the wire bends in the form of a small loop, sufficient to fix the beads, after which the beads and glass beads are strung on the wire in an arbitrary order. The resulting suspension is attached to one of the links in the chain, by bending the wire with its edge wrapped in a loop. Similarly, all the other pendants are manufactured and fastened. After that, the decoration can be used by adjusting its length, fastening the carbine on different links of the chain. As you can see, handicrafts with their own hands - it's not difficult at all, but even a pleasant experience. In addition, they can become just wonderful gifts for friends and family. This method of leisure does not just allow expanding the range of jewelry, but it will also be an excellent way to relieve stress. Manufacture of bead products is also recommended for children, as it has a favorable effect on their development, since it has a positive effect on fine motor skills. Therefore beadwork can become a pleasant family hobby that will bring joy to both mom and her baby.
